Hat section purlin consists of two outward flanges and two vertical sides of the hat. Geometric Steel manufactures top hats for a variety of residential, commercial, and industrial purposes. Manufactured from high tensile galvanised steel (240Mpa and 350Mpa), Galvalume G550, AZ150, and CR in standard lengths up to 6.1 metres, with rib stiffener option.

U sections are frequently used in polyhouses and other specialised applications. This section is manufactured in the most advanced plant in Kurkumbh in thicknesses ranging from 1.00 mm to 3.00 mm, as specified by the customer. Cold roll forming is an energy-efficient and material-saving technology that is commonly used in the manufacture of C purlins and Z purlins and U sections.

L section: The purlin thickness and height are determined by the span length and load for a pre-engineered construction. Such a purlin is necessary for the gable ends. We supply purlins up to 6 metres in length and thickness.

Z purlins are ideal for providing lengthy spans between portal frames on an industrial building. Z Purlins are available in a variety of sizes and material strengths to meet the design requirements of your structure. Z purlins are composed of GI, CR, and HR steel and are roll formed to length with holes punched to your specifications. C & Z Purlins result in cost savings of up to 50% in structural steels when compared to standard sections such as Angle, Channel, and Hollow Section. It is available in conventional lengths, similar to round or square pipe, so no material is wasted.

Access hatches on the roof Any industrial building with a metal roof must have access hatches in order to offer safe and easily accessible access for electrical repairs and roof maintenance. Roof access hatches are built and installed to guarantee security for anyone entering industrial and commercial roofs via stairways or ladders. Because to the hatch's low-profile design, the building's architects were able to keep its straight lines. Additionally, the cost of installing these parts could be far less than that of building the traditional peripheral of a staircase. Usually, an elevated or fixed ladder that is placed outside the building is used to get access to roofs. In order to reduce the psychological harm that psychopaths might cause, it is always dangerous to have access to roof ladders outside of the building's perimeter and to place restrictions on who can reach the roof. In severe weather, using a ladder outside to access the roof could be dangerous. It's not something to think about. It is ideal to have completely safe and secure access to the building's roof from within. The main purpose of geometric steel roof access hatches is to provide industrial buildings with a reliable and secure means of roof access. Roof ladders enable owners and maintenance personnel to get access to the roof for fixes or to perform maintenance.

HAT TOP RIDGE VENT FOR EFFECTIVE VENTILATION. The Hat top Airflow Ridgevent is equipped with two louvers exhaust plates in parallel with the roof slope, as well as a characteristic hat-style cavity Ridge constructed of colour coated galvanise, colour coated galvalume, or galvalume according to customer specifications. Hat Top Airflow Ridgevent is easy to install on any roof profile design, including old profiles. It requires no maintenance because of its long performance life cycle. FEATURES AND BENEFITS • Continuous High natural airflow. • Five metres of airflow. Ridgevent is similar to two whirlybirds. • The internal pressure of structures reduced. • It is available in color-coated steel and may be fitted on any roofing profile. • Available in color-coated steel and all roofing profiles. • Improves and maintains a comfortable living environment. • There's no power, moving parts, or noise • Maintenance-free (no clogging). • Maintains a clean, appealing roofline; hidden beneath louvers and ridge cap. • Increases the life of the building through natural air movement. • Actively prevents the buildup of mould within the ceiling cavity - several health benefits. • Located precisely where they do the most benefit, at the pinnacle of the roof, Airflow Ridgevent are nearly undetectable from ground level and deliver better airflow than other vents. • ADDITIONALLY: Simple to put on existing old roofs. • Maximum space utilisation with an existing structural configuration. • Made in India.

The Sag Rod is distinct from the Turnbuckle Rod or Clevis Rod. It usually requires a pass through of each component it supports, such as C purlins or Z purlins with diameters ranging from 12mm to 16mm. Sag Rods as Lateral Supports for Girts and Purlins. Z sections are widely used for girts and purlins. In many installations, sag rods are utilized to align these members for the connection of steel panels and limit the capacity to bend laterally and twist. This pass-through enables for take-up using regular nuts and washers. There is no requirement for left-hand thread at either end. This Custom Component adds a sag rod between two girts. It also creates holes in the two girts. There are two choices for adjusting the size of the nuts and washers. The first option sizes the nut and washer profiles according to the rod diameter.

Purlin C Purlins are available in a variety of sizes and material strengths (for example, 240 Mpa and 350 Mpa) to meet your building's design specifications. Purlins are perpendicular structural support members in the slope of the roof, with cladding installed on the principal rafter. These roof purlins are widely employed in large-scale infrastructure projects, factories, and warehouses. C purlins are manufactured from quality steel as follows 1. Galvanized C purlin and Z purlin in 240 Mpa and 80 Gsm 2. Galvanized C and Z purlin in 345 Mpa and 120 Gsm 3. C purlin and Z purlin are customized coating and yield strength of steel. 4. Roll formed to the desired length with factory-made punching according to your requirements.

A: The top surface layer is a metal profile sheet that contributes to steel's strength and durability. Available in PPGI/GL/PPGL/AL profiles with 1135mm real and 1060mm cover widths. B: Intermediate Layer: It is a specific insulation material that can be 19 mm, 24 mm, 30 mm, or 50 mm thick, depending on the purpose. C: The bottom lying layer is a metal sheet that provides strength and durability for steel, available in PPGI/GL/PPGL/AL. Thermal Insulated Double Skin Roofing Sheets It is critical that each structure has adequate thermal insulation that is appropriate for its intended use. The system includes composite double skin roof panels and a pre-assembled insulated roof sheet. They are sandwich-style, with insulating filler between two metal layers: a steel-profiled top sheet and plain steel at the bottom. Composite double skin panels come pre-assembled, making installation much easier on-site. The insulation minimises noise and radiant heat; it functions as a circuit breaker, making it ideal for working inside; it is low maintenance and highly rated for thermal performance; and it is a great way to insulate the roof and cladding of any building. omposite panels reduce radiant heat through roofs and walls, keeping your building cool while also lowering your carbon footprint and saving money on ever-increasing energy costs. Solar panel installation is also possible on thermally insulated roof sheets because of their profile benefit. THERMAL-INSULATED METAL ROOFING SHEETS Profile: You can mix-and-match different manufacturers' double skin composite composed of steel, which has the strength and strength of steel Colour Coated Galvanise, Colour Coated Galvalume, and bare Galvalume with the option of our regular colours. 0.50mm thickness. It also comes with off-white simple liner panels that face the building. The inside seems clean and aesthetically nice. Twin skin metal roofs are quick and easy to install, and they combine great performance with variability in insulation thickness based on building utility requirements. A sealed, watertight construction provides total weatherproofing. Width and length: The top sheet measures 0.50mm actual 1135mm with a coverage width of 1060mm spread profile (composed of four valleys and three profiles). The panels are simply lapped and have a cover width of 1060mm when mounted with reduced lap loss and increased cover width. We construct panels to the customer's exact requirements from 600mm to 6000mm in length. Double skin insulation thicknesses include 12mm, 19mm, 24mm, 30mm, and 50mm. Roof lights: Factory-profiled polycarbonate roof lights are used in conjunction with a Thermal Insulated Sheet, which is brought to the job site ready for easy and quick installation. APPLICATION • Warehouse / Cold Storage • Fruit Ripening Chamber Shed • Site Office Building • Chemical Industries • Food Industry • Factory Building